Items where Research Area is "Research Areas > Mechanical, aeronautical and manufacturing engineering"

1999

Adjali, H., Davies, M., Rees, R.W. and Littler, J. (1999) The testing of a numerical model's ability to simulate heat transfer from slab-on-grade floors and the implication for low-energy design. In: Proceedings of the National Passive Solar Conference 1999; 12 -16 Jun 1999, Portland, U.S.A.. ISBN 9780895531711

Blackman, B.R.K., Hadavinia, H., Kinloch, A. J. and Paraschi, M. (1999) Determining the adhesive fracture energy of bonded joints. In: UNSPECIFIED, (ed.) Adhesion Conference. The Institute of Materials, Minerals and Mining. pp. 425-430. 1999

Curley, AJ, Williams, KJ, Le, T and Patel, H (1999) The cyclic fatigue behaviour of ball grid arrays. Microelectronics International, 16(3), pp. 43-45. ISSN (online) 1356-5362

Davies, Michael, Zoras, Stamatis and Adjali, Hicham (1999) A potentially fast, flexible, and accurate earth-contact heat-transfer simulation method. In: Building Simulation; 13 - 15 Sept 1999, Kyoto, Japan.

Fern, A., Mason-Jones, A., Pham, D. T. and Wang, J. (1999) Design and Performance Predictability of Valve Stem Seals Using FEA. (Technical Report) Warrendale, PA., U.S. : SAE International. (SAE Technical Paper 1999-01-0883)

Giaccone, PR, Jones, GA, Minelly, S and Curley, AJ (1999) Motion-compensated multichannel noise reduction of colour film sequences. Journal of Electronic Imaging, 8(3), pp. 246-254. ISSN (online) 1017-9909

Grant, RJ and Smart, J (1999) Crack growth in pin-loaded tubes: part 1: numerical analysis. The Journal of Strain Analysis for Engineering Design, 34(4), pp. 253-269. ISSN (print) 0309-3247

Grant, RJ and Smart, J (1999) Crack growth in pin-loaded tubes: part 2: comparison of experimental data with numerical results. The Journal of Strain Analysis for Engineering Design, 34(4), pp. 271-284. ISSN (print) 0309-3247

Hadavinia, H., Blackman, B.R., Kinloch, A. J., Ring-Groth, M. and Williams, J.G. (1999) The peel testing of adhesively-bonded joints. In: UNSPECIFIED, (ed.) Adhesion Conference. The Institute of Materials, Minerals and Mining. pp. 243-250. 1999

Harjoprayitno, W.W., Hadavinia, H. and Kinloch, A. J. (1999) Epoxy-moulded products: studying and increasing the interfacial adhesion. In: UNSPECIFIED, (ed.) Adhesion Conference. The Institute of Materials, Minerals and Mining. pp. 341-346. 1999

Liu, F. and Wen, J.X. (1999) Development and validation of an advanced turbulence model for buoyancy driven flows in enclosures. International Journal of Heat and Mass Transfer, 42(21), pp. 3967-3981. ISSN (print) 0017-9310

Monekosso, Ndedi (1999) On-board reasoning for an autonomous spacecraft. (PhD thesis), University of Surrey, .

Philbin, Simon, Millar, Ross and Coombes, Robert (1999) Studies of novel nitro substituted nitrogen heterocyclic compounds. In: National Defense Industrial Association (NDIA) Annual Symposium on Insensitive Munitions and Energetic Materials Technology; 10-12 Nov 1999, Tampa, U.S.A.. (Unpublished)

Sabir, H. M. and Eames, I. W. (1999) Performance of film absorbers under the effect of a contaminant non-absorbable gas. Applied Energy, 63(4), pp. 255-267. ISSN (print) 0306-2619

Sabir, H.M., Eames, I.W. and Suen, K.O. (1999) The effect of non-condensable gases on the performance of film absorbers in vapour absorption systems. Applied Thermal Engineering, 19(5), pp. 531-541. ISSN (print) 1359-4311

Talal, Sina (1999) Effect of long-term compression on rigid polymer foams. (PhD thesis), Kingston University, .

Zhang, T., Evans, J.R.G. and Bevis, M. (1999) Relaxation patterns in powder injection mouldings made with repeated flow reversals. Journal of the European Ceramic Society, 19(4), pp. 411-417. ISSN (print) 0955-2219

Zweiri, Yahya, Whidborne, J. F. and Seneviratne, L. D. (1999) Dynamic simulation of a single-cylinder diesel engine including dynamometer modelling and friction. Proceedings of the Institution of Mechanical Engineers - Part D: Journal of Automobile Engineering, 213(4), pp. 391-402. ISSN (print) 0954-4070